Departments ELECTRICAL ELECTRONICS DESIGN AND CONSTRUCTION OF A MICROCONTROLLER BASED DOT MATRIX ADVERT DISPLAY

2k views/   FMT: MS Word/   Chts 1-5 BrilliantNG
₦ 3,000.00 3,200.00

DESIGN AND CONSTRUCTION OF A MICROCONTROLLER BASED DOT MATRIX ADVERT DISPLAY
DESIGN AND CONSTRUCTION OF A MICROCONTROLLER BASED DOT MATRIX ADVERT DISPLAY

CHAPTER ONE

INTRODUCTION

The purpose of this project is to produce a narrative description of the design and construction of a microcontroller based dot matrix advert display. Firstly computer aided design is the modeling of physical system on Computers allowing both interactive and automatic analysis of design variant and the expression of design in a form suitable for manufacturing. This follows by explaining the microcontroller based dot matrix advert display as a device which is fast gaining wide acceptance and application in the present days due to its ability to provide a very high precision timing. The dot matrix advert display can be describe as an electromechanical system for processing information in which the information is represented by physical quantities, which are so constrained to take only discrete values that can be referred to as binary signals.

In this design we have implored the use of both hardware and software to bring about the entire project. The hardware components are solely coordinated by the AT89S51 micro controller chip while the C programming language is used to program the chip.

1.1 OBJECTIVE OF THE PROJECT DESIGN

Depending on ones intention, microcontroller based dot matrix advert display system have many aims and objectives.

For instance, this one in particular aims at displaying a moveable coded letters that says UNIVERSITY CAFETERIA

Also microcontroller based dot matrix advert display system can be used to control the traffic misunderstanding among motorists especially in junctions. This is achieved by displaying stop, get ready, or move. Some traffic control electronic system displays symbols or color that represents the stated commands above

Moreover, microcontroller based dot matrix advert display system is used in electronic scoreboard during football matches to display when a goal is scored, also to display the name of that player who scored the goal. Above all, this system has contributed a lot in boosting advertisement.

1.2 PREAMBLE

Micro controller programmable Dot matrix information display system, is a system electronically designed and constructed, that is used to display different information to the view of the masses. The information to be displayed could be diagrams, symbols, letters, colors, numbers, codes, etc depending on what is needed at a particular place and time. This without doubt, has made life easier for the people in different ways; however microcontroller, which is the heart of this system, can be described thus: A micro controller is a computer. All computers, whether we are talking about a personal desktop computer you are using is a general purpose computer that can run any of thousands of programs. Microncontrollers are special purpose computers. Micro controllers do one thing well. There are a number of other common characteristics that define micro controllers. If a computer matches a majority of these characteristics, then you can call it a micro controller,

1 Micro controllers are embedded inside some other device often a consumer product so that they can control the features or actions of the product. Another name for a micro controller, therefore, is embedded controller

2 Micro controllers are dedicated to one task and run one specific program. The program is stored in ROM read only memory and generally does not change. Micro controllers are often low power devices. A desktop computer is almost always plugged into a wall socket and mighty consumes 50 watts of electricity. A batteryoperated micro controller might consume 50 milliwatts.

3 A micro controller has a dedicated input device and often but not always has a small LED or LCD display for output. A micro controller also takes input from the device it is controlling and controls the device. Meanwhile the use of a microcontroller to implement an electronic display system design made up of LEDs connected in common cathode matrix form is referred to as microcontroller based programmable dot matrix information display system. This project design is a welcome compliment that displays UNIVERSITY CAFETERIA

1.3 JUSTIFICATION OF THE PROJECT

Due to the various problems encountered in the manual/analog design and construction of signposts for advertisement, there is every need for an automated electronic display system that will solve this problem. This will ensure that viewers get the adequate information that is displayed in good and attractive colors. The though the manual/analog way of displaying information to the view of the people is still targeted viewer are attracted. The height in which advertisement in Nigeria have attained will be maintained if some of its design/construction operation is computerized Micro controller based information display especially the ones that has to do with bigger companies. This will also maintain the good relationship between the company and its numerous customers.

1.4 SCOPE OF THE PROJECT

This project can serve in any aspect of life this project microcontroller based dot matrix advert display is based on a computer aided design. .

In the implementation of this project, the scopes that I shall concentrate more on are: the architecture of the microcontroller port interface, multiplexing the data port control sequence and algorithm of the traffic light. The features of the

AT89S51 were exploited to achieve the desired sequence of operation of this project.

1.5 CONSTRAINTS

One of the obvious constraints I had in the course of this project was the scarcity of sometimes outright unavailability of some of the required components in the markets. Since scarcity is followed by a hike in price, when such components were even found, they were out rightly expensive. Another major constraint I had was time constraints. I had a relatively short time to source out materials from net, libraries, etc, fully understand the underlying principles and come up with a design that would work. As a result, I had to forgo pleasure and even leisure in order to achieve this.

1.6 BLOCK DIAGRAM OVERVIEW

The entire project given as an overview is shown in diagrammatically in Fig 1. Below

As the name implies, this project is microcontroller based, hence a microcontroller called AT89c51 is employed to serve the purpose with RAM and some other discrete components that are to be discussed later. In other to reduce the risk and complications involved in using only discrete components the project is made up some integrated circuits.

Meanwhile, this project, microcontroller based dot matrix advert display system has sub units such as:

The mains unit.

The power supply unit

The switching and timing unit

The address generators unit

The memory unit/ Microcontroller

The drivers unit

1.7 PROJECT REPORT ORGANIZATION

Six chapters were covered in the course of design and development of this project. The chapters and their contents are as follows:

Chapter one is the introductory chapter that gives the aim, scope and justification for the project. This part shows the significant and the justification of this project that is the literature review of microcontroller dot matrix advert display system and its components reviewed, also the history of the project and its uses were discussed. Chapter Two is literature review. It deliberates on different related works done by several authors with dates. It also discusses on the limitations of some of these works.

In chapter three, I discussed the practical system analysis based on what a microcontroller based dot matrix advert display system will do when fully constructed and installed. Also discussed is the requirement analysis, which is all the information, gathered form a wide research on microcontroller based dot matrix advert display board, data analysis, system design approaches, topdown, bottomup, choice of design approaches, data flow arrangement and the system flow chart are also discussed. Chapter four deals with the design/preliminary design of how the system will achieve its function, all these are illustrated here in form of circuit diagram to show how the main system is linked to the sub system or the modules. Also discussed here is the user interface design that comprises the input design and the output design. The software design and implementation is also discussed in this chapter. The choices of programming language, softhard, and subsystem implementation is also discussed here. In chapter five I discussed the system testing and the appropriate software testing strategy to achieve the expected result and the actual. The performance evolution is also analyzed here. Also discussed is the system testing and integration, how the components were tested. The reference evaluation and cost analysis is also discussed here. Finally the summary of this project is discussed in detail in chapter six. The contributions of the project, achievements, and problems for further enhancement, development and advanced discussions on this topic


View Related Projects

DESIGN AND CONSTRUCTION OF AN AUDIO AMPLIFIER
462 views/   FMT: MS Word/   Chts 1-5
3,000.00 3,200.00

ABSTRACTThis project involved design and construction of an audio amplifier that could drive a quite number of speakers...

Continue reading
Dept: ELECTRICAL ELECTRONICS
DESIGN AND CONSTRUCTION OF A MINI FM TRANSMITTER
389 views/   FMT: MS Word/   Chts 1-5
3,000.00 3,200.00

1.0. GENERAL INTRODUCTION1.1. AN OVER VIEW OF MODULATION:In communication engineering, modulation is a ve...

Continue reading
Dept: ELECTRICAL ELECTRONICS
DESIGN AND CONSTRUCTION OF DC TO AC STATIC INVERTER
373 views/   FMT: MS Word/   Chts 1-5
3,000.00 3,200.00

1.0. INTRODUCTION:A DC to AC inverter is a simple device that produces an AC output from DC supply. The techni...

Continue reading
Dept: ELECTRICAL ELECTRONICS